Woods 1009 loader manual

A weld-on, conversion plate converts the original bucket to accommodate the quick attach. Two spring-loaded, over-center latches hold attachments firmly in place on the loader. The latching pins are hardened and tapered for easy operation and long life. Converts Woods loaders with pin-on buckets to allow the use of skid loader compatible universal attachments. Standard duty bracket to weld to existing bucket after pin brackets are removed included Allows the use of skid steer-type attachments Weight of face plate 78 lbs.

Weight of weld-on bucket bracket 51 lbs. Share or Email This Post. Print This Page. Reviews There are no reviews yet. The is a pillar style mid mount. The is a full frame from the looks of the pics. That's about the only thing I can see that would make any weight difference. Like what was stated in the other post, probably just different manufacturers. Apr 22, 6. Wher did your lb figure come from?

I show that as being the weight of a model. The also has slightly higher lift and breakaway capacities, and larger rollback and dump angles.

Apr 23, Thread Starter 7. My Woods loader brochure shows the at lbs. The Woods website see links above. What your brochure has makes a lot more sense to me. I'm pretty sure it's a typo on their website. I sent Woods a email but have not received a reply. Unfortunately, I can't find the weight for the LA The Kubota dealer I spoke to last week did not give me much feedback about how the two compare. Only that the Woods is made to be more universal and uses a bracket to adapt to different tractors.

I was hoping to get a little more info from the dealer. I would like to do business with this dealer, he is out of state NJ and I could save the sales tax. You must log in or register to reply here. Replace if damaged. See Parts section for location. Do not install 4-point sub-frame on a tractor without a Woods or OEM loader mount attached. Leave all hardware loose until sub-frame has been fit up or otherwise specified in the instructions. This mount can be installed on tractors equipped with a New Holland mid-mount mower.

Sub-frame can be installed with mower attached but may be easier if mower is removed from tractor. Place jackstands under rear axle and remove both rear tires. Disconnect the anti-sway bars Figure 1 from the anti-sway brackets and remove front half. Store front half of anti-sway bars for later use when backhoe is removed. Attach back half of anti-sway bars to the side of 3- point arm to prevent them from pivoting during backhoe operation.

Remove ROPS hardware and spacer from both sides of rear axle. See Figure 2. With spacer removed, cut bottom flange off of spacers. Spacer will be reused when sub-frame is installed. Make sure cut is flush with side flanges. See Figure 3. As a valued customer, Woods appreciates your comments.

Once sub-frame and hydraulic hoses have been installed, please take a few minutes to complete the Sub-Frame Mount Evaluation sheet that was supplied with your sub-frame. Your comments will help us continue to bring you quality products.

Attach front mount 32 to the right loader mount using two cap screws 26 , hardened flat washers. Attach left front mount 8 to tractor using two cap screws 20 and hardened flat washers If mid-mount is installed use cap screws See Figure 6. Attach right front mount 9 to tractor using two cap screws 20 and hardened flat washers Figure 7.

Figure 6. Left Front Mount Installed. Place left tractor bracket 2 under left side of tractor. Use a hydraulic floor jack to help raise and hold tractor bracket in position.

Attach left tractor bracket 2 to left loader mount using two cap screws 26 , hardened flat washers 23 , and hex nut Attach tractor bracket to the bottom of rear axle using two cap screws 16 , four hardened flat washers 22 , hex nuts 15 , and modified spacer.

Place right tractor bracket 1 under right side of tractor. Attach right tractor bracket 1 to front mount 32 using two cap screws 26 , hardened flat washers 23 , and hex nut Attach left tractor bracket to left front mount 8.

Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password.

Woods Equipment. Woods Equipment User Manual Download for 1. It Include manual backhoe safety, repair contains not and operation, informationother part in.

Includes Hose Kit Tested. Safety Rules continued on next page. Safety Rules continued from previous page Make sure all hydraulic hoses, fittings, and valves are in good condition and not leaking before starting power unit or using equipment.

Remove top link. DP11 Figure 1. Remove Flange. Pictures show mid-mount installed. See Figure 5. See DP4 Figure 7. Left Front Mount Installed Figure 7.